Spectra Watermakers 1/2HP MOTOR 12V 2000 RPM 48YC TEFC EL-MTR-1/2HP12
- Replacement electrical/control component (switch, sensor, board, fan, etc.) for Spectra/Daily Watermakers systems.
- Replace if the component fails electrically, shows corrosion, or troubleshooting points to the part.
- Best practice: verify by part number and system model/serial before ordering, especially on older or modified systems.
Key Fitment Details
- Part No.: EL-MTR-1/2HP12
- Voltage: 12V
- Horsepower: 2 HP
- Speed: 2000 RPM
- Motor Enclosure: TEFC
- Frame: 48YC
F.A.Q.
- What is this part used for?
Replacement electrical/control component (switch, sensor, board, fan, etc.) for Spectra/Daily Watermakers systems. - How do I confirm it is the correct one?
Match the part number and compare key specs (sizes, voltage, ports). If you have your watermaker model and serial number, we can confirm before you order. - Any service tips?
Disconnect power, match connectors, and confirm ratings (voltage/amps) before installation. - Good to know:
If you are troubleshooting, send your model/serial and a brief symptom description - we can help confirm the right part.
Check your installed configuration
Match manufacturer part number EL-MTR-1/2HP12 to the parts diagram for your installed system. Model family alone does not establish compatibility. Use the documented configuration requirements on this page where available.
Additional Parts You Might Consider:
Also helpful:
- Dielectric grease for connectors in wet environments
- Check/clean grounding and inspect any corroded terminals
Questions? Visit our Contact Page to speak to our watermaker experts.
We Ship Internationally, Contact us For a Shipping Quote!
All documented configurations and requirements
Each group applies only to the listed configurations and installed hardware. Match the conditions and manufacturer references before ordering.
Documented configurations
- Newport 400 Mk II · MPC 5000 · Match installed voltage and hardware
Original 12V half-horsepower, 2000 RPM, 48YC motor configuration. A later 24-to-12V retrofit requires conversion and controller setup; do not select by vessel input alone. System input: 12 V; retain the specified component supply and wiring.
Documented configurations
- Newport 400 Mk II-Z · MPC 5000 · Match installed voltage and hardware
Original 12V half-horsepower, 2000 RPM, 48YC motor configuration. A later 24-to-12V retrofit requires conversion and controller setup; do not select by vessel input alone. System input: 12 V; retain the specified component supply and wiring.
Documented configurations
- Newport 400C · Connect · 12 VDC · Compact / short membranes · NP-400C-12S
- Newport 400C · Connect · 12 VDC · Standard / long membranes · NP-400C-12
- Newport 400C · Connect · 24 VDC · Compact / short membranes · NP-400C-24S
- Newport 400C · Connect · 24 VDC · Standard / long membranes · NP-400C-24
Newport 400 mag-drive 12V/24V system configuration: manufacturer moved both to a 12V motor in summer 2022. Replacing an older 24V motor requires PWM reprogramming and the complete bulletin procedure; not a drop-in substitution.
Parts diagram / guide, page 1 · Parts diagram / guide, page 89
Documented configurations
- Newport 400C · Connect · 12 VDC · Compact / short membranes · NP-400C-12S
- Newport 400C · Connect · 12 VDC · Standard / long membranes · NP-400C-12
- Newport 400C · Connect · 24 VDC · Compact / short membranes · NP-400C-24S
- Newport 400C · Connect · 24 VDC · Standard / long membranes · NP-400C-24
- Newport 400C · Connect · 48 VDC · Compact / short membranes · NP-400C-48S
- Newport 400C · Connect · 48 VDC · Standard / long membranes · NP-400C-48
current Newport 400 Connect feed motor/controller. Match installed assembly, port/thread or tube dimensions, material and pressure duty; documented original arrangement only. System input: 12/24/48V; retain the documented component supply and wiring. Current May 2025 module with its documented supplies. Older 24V motor replacement requires the conversion bulletin and PWM reprogramming; not a drop-in swap.